Aerospace Knowledge and Technology Journal

Aerospace Knowledge and Technology Journal

Aerospace Knowledge and Technology Journal

Journal Archive

Most Visited Articles
The effect of loss parameters using tandem blade in axial compressor
Investigation of Fin Span Effect on Performance of Missile on its Aerodynamics Analysis
Fracture parameter determination for a thin walled pressurized cylinder under the influence of residual stress induced by welding process
Experimental study and Optimization of Manufacturing Parameters of High Silica-Phenolic/Glass-Epoxy Laminate insulators in order to achieve the Highest thermal resistance and inter-laminar Strength
Integrated guidance and control of the surface-to-air homing missile Pitch channel using optimal neural network
Design of a Navigation System for an Unmanned Air Vehicle Equipped with a Bearing-Only Sensor
Computational Investigation of Mach number and angle of Attack Effects on the Flow Pattern over a 60º Delta Wing
Current Issue: Volume 15, Issue 1, September 2026 

Keywords Cloud

  • Optimization
  • numerical simulation
  • UAV
  • satellite
  • flow control
  • Multi-objective optimization
  • genetic algorithm
  • Uncertainty
  • Modeling
  • Sensitivity analysis
  • Heat Transfer
  • Attitude control
  • Missile
  • Simulation
  • optimal control
  • Piezoelectric
  • integrated guidance and control
  • Numerical method
  • quadrotor
  • finite element method
  • Nanocomposite
  • Inertial navigation
  • fault detection
  • Computational fluid dynamics
  • modal analysis
  • supercritical airfoil
  • launch vehicle
  • thrust
  • Cavitation
  • Aerodynamic coefficients
  • oscillating airfoil
  • FEM
  • Carbon Nanotube
  • Control
  • Neural network
  • three-body problem
  • supersonic flow
  • Thermal management
  • delta wing
  • Performance
  • energy absorption
  • Trajectory Tracking
  • Combustion chamber
  • Finite element
  • Calibration
  • liquid fuel
  • flight simulator
  • semi elliptical crack
  • Fault tolerant control
  • design optimization
  • Rudder
  • Transverse Injection
  • Bending test
  • Corona Plasma Actuator
  • Groove
  • Free vibration
  • temperature gradient
  • Sound transmission loss
  • propulsion
  • nanofluid
  • flow visualization
  • Humidity
  • free convection
  • fault estimation
  • Constrained optimization
  • Cooling
  • Diesel
  • Artificial neural network
  • Reinforcement Learning
  • Plasma Actuator
  • PCM
  • CFD
  • Adaptive control
  • cavity
  • Magnetic field
  • Feedback linearization
  • central crack
  • unmanned aerial vehicle
  • PID Controller
  • Combustion Efficiency
  • hazard rate behavior
  • stewart platform
  • parity relation
  • Heat Pipe
  • statistical analysis
  • Wind Tunnel
  • Axial compressor
  • inverse dynamics
  • Kerosene
  • Porous materials
  • Insulation
  • UAV security
  • flying wing
  • trajectory optimization
  • Unsteady turbulent flow
  • Pareto Front
  • Active Vibration Control
  • Target Tracking
  • transient
  • Attitude Determination
  • Robust control
  • Spray Characteristics
  • Scramjet
  • liquid propellant engine
  • Path Planning
  • multidisciplinary design optimization
  • voltage
  • Film cooling
  • Conceptual design
  • reaction wheel
  • interior ballistics
  • Lagrangian points
  • total pressure loss
  • Mass Flow
  • guidance law
  • Buckling
  • aerodynamic efficiency
  • Spray
  • Axial turbine
  • OpenFOAM
  • optimal design
  • Flexible Satellite
  • angle of attack
  • optimal reliability modeling
  • sensor
  • Supersonic
  • turbojet engine
  • Fouling
  • experimental method
  • frequency response
  • Magnetohydrodynamic
  • neural control
  • Blowing ratio
  • near-Earth asteroids
  • Classic controller
  • heat transfer rate
  • Comprehensive Preference-based Design (CPD)
  • Stress transfer
  • third order shear deformation theory
  • power off
  • Aerodynamic forces
  • hardware-based satellite simulator
  • RANS
  • UAM
  • MEMS inertial sensors
  • spiral atomizer
  • structural design
  • Navier-Stokes equation
  • Aircraft Design
  • Stall
  • passenger aircraft
  • Cutout
  • Modified Stir casting method
  • design parameters
  • Triple Jets
  • navigation system
  • design structured matrix (DSM)
  • Bandwidth
  • Vibration Control
  • static coefficient
  • Inverse kinematic problem
  • \"Telescopic Booms\"
  • Flying Targets
  • nonlinear observer
  • improvement
  • Nonlinear dynamic
  • mini-turbojet engine
  • Aero gas turbine engine
  • functional guidance
  • impeller
  • space security
  • local damage model
  • diamond lattice
  • geometric secrecy
  • time delay
  • Output power
  • free transverse vibration
  • Multi-phase
  • linear regression
  • functionally graded viscoelastic materials
  • classical laminated plate theory
  • carbon nanotubes (CNT)
  • systematic design
  • Pressurized swirl injector
  • numerical flow simulation
  • social intelligence
  • thrust vector
  • approximate and near optimal solution
  • Probabilistic Neural Network
  • Decentralized Formation control \"
  • adhesively bonded joint
  • Electrical discharge machining
  • Performance tests
  • three dimensional elasticity
  • pitch angle
  • flexural loading
  • extended state observer (ESO)
  • Uncertain Cost Function
  • Encrypted control
  • \"